ELIMKO MALAYSIA SINGAPORE, ELIMKO SINGAPORE DISTRIBUTORS, ELIMKO MALAYSIA DISTRIBUTORS

STANDARD CODE
It is coded with digits and letters containing the drawing number and 5 separate pieces of information.
 
ADDITIONS TO STANDARD CODE
In addition to the technical specifications contained in the standard codes, the required features are listed in the '' ADDITIONS TO STANDARD CODE''. These features are given below.

STANDARD CODE
It is coded with digits and letters containing the drawing number and 8 separate pieces of information.
 
ADDITIONS TO STANDARD CODE
In addition to the technical specifications contained in the standard codes, the required features are listed in the '' ADDITIONS TO STANDARD CODE''. These features are given below.

STANDARD CODE
It is encoded with digits and letters containing the drawing number and 8 separate pieces of information.
 
ADDITIONS TO STANDARD CODE
In addition to the technical specifications contained in the standard codes, the required features are listed in the ''ADDITIONS TO STANDARD CODE''. These features are given below.

Straight type thermocouples coding table is applied exactly for the selection of the thermocouples of the inset type TC03, TC04 and TC30. For this type of thermocouples length is written in cm. Length for inset types are written in the code list in mm. Also the lengths to be installed inside the standard lengths are standard.

For code generation for L type thermocouple selection, the straight type thermocouple coding list is used Type L thermocouple drawing can be TC06 or TC07. As you can see in the drawing below, L1 size is Immersion length. In the L-type thermocouple code, the figure in height is L1. In standard types, L2 length is automatically determined when L1 is detected.

Straight thermocouples with metal and ceramic protecting tubes are widely used in a variety of processes between –200 °C and 2320 °C The maximum operating temperatures given in the catalogue apply to the air where there are no corrosive gases.
 
EMF characteristics of the thermocouples in this catalogue conform to DIN 43710 and IEC 60584 standards.

E-RHT-10 is a microprocessor based transmitter that uses a single chip relative humidity and temperature sensor module. The single chip sensor provides 12/14 bit (humidity / temperature) serial digital output for each reading. The sensor includes two calibrated micro sensors for relative humidity and temperature.

E-KC-200-H is a head-mounted type two-wire temperature transducer conforming to the HART protocol. Converters converts the measured value to a 4-20mA current signal according to the configured scale. Thermocouple and resistance thermometer type temperature sensors can be connected to the input of the converter.

E-KC-100 Series head type temperature converters are electronic units designed by using microcontroller, inside plastic roller, capable of being installed inside thermocouple or resistance thermometer head. They convert the thermocouple and resistance thermometer values into a standard 4-20mA current signal in all areas of the industry.

E-RLT-100 series Radar Level Sensors are designed to measure the level of material in silos. 24 GHz K-Band FMCW Radar provides high resolution reliable measurement with narrow beam microwave transmission. Optional two-wire 4-20mA electrical interface with optional HART output simplifies installation and reduces maintenance costs.

Resistance Thermometers are used widely from -200 to +850°C in different processes. Especially at low temperatures, resistance thermometers are preferred since their accuracy is much better than thermocouples. Up to 500°C standard types and between 500 - 850°C special types are used.

Suitable for cabinet mounting, the E-VS-100 Series vibrator drivers are microprocessor based, designed to drive vibrators used for product feeding in blending, dozing, bagging and filling systems.

E-AC-10 series weight converter is designed using microcontrollers for weighing applications. Weight information is taken from the load cells connected to the device and displayed on the indicator.
 
5 keys located on the front panel of the device are used for programming and other functions (calibration, taring, etc.).

E-RHT-10 is a microprocessor based transmitter that uses a single chip relative humidity and temperature sensor module. The single chip sensor provides 12/14 bit (humidity / temperature) serial digital output for each reading. The sensor includes two calibrated micro sensors for relative humidity and temperature.

E-AR-20 Series digital wood moisture content meters are designed by using new generation micro-controllers. Unit dimensions are 96x96 mm, confirming to IEC/TR 60668 and programmable easily. E-AR-20 is used at such industrial benches as wood process & coating, chipboard production etc.

E-1200 Series flow measurement instruments are new generation micro-controller based industrial instruments designed for flow measurement processes.
 
E-1200 Series dimensions are 96x96 mm, conforming to IEC/ TR 60668. The unit has a 4 digit flow rate and 6 digit totalizer display.

E-DB-10 Series Flow Computer is designed using new generation micro-controllers for flow measurement needs with temperature and pressure compensation. E-DB-10 Series dimensions are 96 x192 mm, conforming to IEC/TR 60668. The instrument’s universal inputs and outputs can be easily programmed by the user.

E-KC-200-H is a head-mounted type two-wire temperature transducer conforming to the HART protocol. Converters converts the measured value to a 4-20mA current signal according to the configured scale. Thermocouple and resistance thermometer type temperature sensors can be connected to the input of the converter.

E-KC-100 Series head type temperature converters are electronic units designed by using microcontroller, inside plastic roller, capable of being installed inside thermocouple or resistance thermometer head. They convert the thermocouple and resistance thermometer values into a standard 4-20mA current signal in all areas of the industry.